A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
The article author is making a few great observations on the subject of A Step-by-Step Guide to Installing a Bathtub in general in this post in the next paragraphs.
Mounting a bath tub isn't specifically rocket science, yet it does require solid plumbing, woodworking, and sometimes, tiling skills. Changing an old bathtub with a brand-new one is additionally a reasonably difficult task. If the old bathtub is easily available, the job can relocate immediately; if you have to open up a wall to eliminate the old tub and position the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. Ensure you have actually qualified yourself for the task and fit trying it. Rather than employing a contractor to take over a halfway-completed task, it is much better to take into consideration using one before you begin. Chances are you might require a specialist plumber to make tube links.
This article will certainly aid you mount a brand-new bathtub in your washroom if you have actually already bought a brand-new tub as well as do not require to change the arrangement of your previous water system pipelines.
Your devices and also material list should comprise the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you must do is disconnect the water system. After doing so, activate the taps to drain pipes any type of water staying in the system. The procedure of getting rid of the existing faucets can be quite problematic because of the limited access that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a cloth prepared for the remaining water that will come from the pipes. When the supply pipes have actually been eliminated, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing substance.
Before proceeding to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers remain in area between the tap and the sink. Protect the faucet in position with the manufacturer offered backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap connectors. The former kind should be connected to the faucet ends first, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Tub
Making use of the two wood boards under its feet, position the bath tub in the required setting. The wood boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four small factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level as well as changing the feet on the bathtub till the spirit level checks out degree.
To mount faucets, fit all-time low of the outermost versatile faucet port to the suitable supply pipe by making a compression join; after that do the exact same for the various other tap.
Activate the water and examine all joints and also new pipework for leaks as well as tighten them if essential. Load the bathtub as well as likewise examine the overflow outlet as well as the regular electrical outlet for leakages.
Lastly, fix the bathroom paneling as defined in the maker's user's manual. Tiling and securing around the bath tub should wait up until the bath tub has been used a minimum of once as this will resolve it into its last placement.
Planning for the Installment
Firstly, the supporting structure supplied with the bathroom needs to be fitted (if called for) according to the supplier's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to make certain that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the flexible faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be suited its last placement.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a stiff seal, creating the water to pass through the wall between the bathroom and the tiling, resulting in problems with wetness as well as possible leakages to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and installations. They are sold in tubes as well as cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to allow for the movement experienced when the tub remains in use. The sealant can split fairly early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the market. It is advisable to fit the ceramic tiles using water-resistant or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very curious about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I am praying you appreciated my piece. Remember to set aside a second to share this blog entry if you liked it. Thank you so much for going through it.
Further Details Report this page